Wireless

REMOTE CONTROL

Options

Options available
 

Technical

Technical informations

note options shown in this chart can

vary depending truck and/or options

Brochure

Download Brochure

INSULATED 50'

AERIAL LADDER


The RH50D is an insulated telescoping ladder with a working height of 50 ft. (15.24 m), comprising three ladder sections for optimal effectiveness. Ideal for work requiring a longer reach (e.g., utility poles offset far from the road) since the side reach can take you all the way to 39 ft. (12 m). The lift ring located at the end of the second section is a standard accessory and can lift loads of 550 lbs (250 kg) in any position, regardless of the chosen vehicle.

 

This unit can be installed on different chassis as long as the GVWR (gross vehicle weight rating) is greater than 19, 000 lbs (8,620 kg) like Hino, Mitsubishi, International, Freightliner and so many more. And that’s not to mention the many other benefits and options available to ensure that RH aerial ladder equipment meets your precise needs.

 

Key in hand option is available. Please contact us to see what we can do for your preferred chassis and configuration.


Specification
Est. working height  (A)11.58m (38')13.41m (44')11.58 m (38'
Horizontal reach      (B)8.39m (27’6'')10.05m (33’)8.39 m (27' 6")
Length (retracted)   (C)4.56m (15')5.17m (17')4.37 m (14' 4")
Interior width           (D)49 cm (19")49 cm (19")49 cm (19")
Bucket capacity159 kg (350 lbs)159 kg (350 lb)159 kg (350 lb)
Lifting ring 250 kg (550 lbs)250 kg (550 lbs)250 kg (550 lbs)
Rotation360° continuous (opt.)360° continue (opt.)360° continue (opt.)
Elevation degrees-8° to 80°-5° to 80°-5° to 80°
Approx. weight498 kg (1100 lbs)567 kg (1250 lbs)658 kg (1450 lbs)
GVWR min. required4309 kg (9500 lb)7938 kg (17500 lbs)8620 kg (19000 lbs)
Hydraulic pressure20684 kPa (3000 psi)20684 kPa (3000 psi)20684 kPa (3000 psi)

 

* Informations shown can vary depending on truck and/or options
ask a representative for more details

BATTERIES

OPERATED

The connection of the auxiliary battery isolates the vehicle’s aerial lift equipment. The unit will work without the vehicle engine on. In any case, it will affect the vehicle’s battery; it is actually an additional security because if the truck’s battery needs a little “boost”, due to the type of connection, it can feed of the auxiliary battery. All our units have a two-way splitter between the auxiliary battery and the vehicle. We make no modification to your vehicle, only a wire is connected to the alternator which is used to recharge the auxiliary battery when the vehicle is running.

 

In addition, we can provide additional security by adding a system such as Ozone-tech. This product requires removing the keys from the ignition; press an activator button to operate the unit. Ozone-tech is perfect for fleet owners that want to have some control over the fuel consumption. The system ensures optimum battery management and will turn on the engine if the vehicle needs to recharge the battery to its maximum capacity.

Advanced

Design

& Engineering

RH Ladder uses advanced structural optimizing simulations to ensure safety and  enhance toughness. Our engineering approach considers all attributes such as weight, resistance, quality, performance and  manufacturability.

IMPORTANT

note:

This type of aerial ladder must be installed on vehicles whose GVWR (gross vehicle weight rating) is greater than 9,500 lbs (4,309 kg). Outriggers are generally not required. However, given the variety of configurations possible, outrigger requirements must be confirmed by means of stability tests performed on your bucket truck. 

 

The same applies to the bucket’s load-carrying capacity (in other words, the maximum weight authorized to be carried in the bucket). Specifically, this telescoping ladder is rated to carry 350 lbs (159 kg); however, its actual load-carrying capacity depends on the carrier vehicle. 

 

We encourage you to contact Robert Hydraulique to obtain more information on the restrictions and factors to be taken into account when installing RH telescoping aerial ladders so that you can meet the highest standards in quality and safety. 

 

*** Always ensure that you are complying with all local regulations when installing bucket-equipped aerial ladders. Robert Hydraulique is not responsible for installations performed outside of its production facilities
 

HIGH PRECISION

MANUFACTURING

ROBOTIC WELDING

Accuracy is crucial to achieve consistent quality. RH Ladder uses waterjet and laser cutting, along with robotic welding to deliver constant precision and reliability.


Waterjet Cutting


Numeric tooling technologies